Nest 0 Cart
Nest Account
Popular Exams
All Categories...
Nest
Nest 0
Contact
Log In / Sign Up
Copyright 2024 © store. All rights reserved.
Home Dell DSDPS-200

Dell DSDPS-200 Exam Practice Questions (P. 3)

  • Full Access (56 questions)
  • Six months of Premium Access
  • Access to one million comments
  • Seamless ChatGPT Integration
  • Ability to download PDF files
  • Anki Flashcard files for revision
  • No Captcha & No AdSense
  • Advanced Exam Configuration
Get Contributor Access
Question #11
An administrator needs to change the RAID type from RAID 10 to either RAID 50 or RAID 6.
What must the administrator select before Modify RAID Configuration within the Activities pane?
  1. A
    Tools within the Tool pane
  2. B
    Storage Pools within Group pane
  3. C
    Member within the Group pane
  4. D
    Group Configuration within the Group pane

Correct Answer:
B
Pools allow you to organize storage by RAID type.

Question #12
According to Dell recommendations, when should a firmware update be performed on a PS Series group?
  1. A
    Firmware upgrades should be performed on the weekends.
  2. B
    Firmware updates should be done during low I/O periods.
  3. C
    Firmware updates must always be done during a maintenance window.
  4. D
    Firmware upgrades may be performed during any I/O period.

Correct Answer:
B
Dell recommends that you perform firmware updates during periods of low activity. If possible, perform the update after a backup.
References: Updating Firmware for Dell EqualLogic PS Series Storage Arrays and FS Series Appliances, page 9 http://en.community.dell.com/dell-groups/dtcmedia/m/mediagallery/20381147/download

Question #13
A VMware administrator requests the creation of a 100 GB volume to use as a datastore on an ESX environment. The SAN administrator completes the request.
For a few days, the VMware administrator is able to access and use the datastore. The VMware administrator then reports that the VM located on the datastore is greyed out and labelled as inaccessible.
What are three possible reasons for this problem? (Choose three.)
  1. A
    The SAN administrator has NOT set the datastore access policy.
  2. B
    The SAN administrator recently upgraded firmware revision on the array.
  3. C
    The SAN administrator has changed and set an incorrect access policy.
  4. D
    The SAN administrator set the datastore volume as "Read Only".
  5. E
    The ESXi host is unable to ping the Storage group.

Correct Answer:
BCE
Incorrect Answers:
A: The datastore access policy worked fine for a few days.

Question #14
A customer has a multi-member, multi-pool group in production. The load on the pools is NOT balanced.
Which two methods should a SAN administrator use to balance the load between the pools? (Choose two.)
B. Within the Group Manager Volumes tab, right-click a volume, select "Move Volume".
D. Within the Group Manager Group tab, right-click a volume, select "Move Volume".

Correct Answer:
AB
To move a volume to a new pool:
1.Click Volumes.
2.Expand Volumes and select the volume name.
3.Click Move volume to open the Move volume dialog.
4.If you are changing the pool assignment for a synchronous replication volume, you must specify the SyncActive or SyncAlternate volume.
5.Select the destination pool for the volume.
6.Click OK.
The volume status is shown as moving until the pool move operation completes.
References:
http://psonlinehelp.equallogic.com/en/V6.0/groupmanager.htm
(Moving a Volume to a Pool)

Question #15
A customer is moving to a new datacenter and needs to put the existing two members into a new subnet. Each array has two iSCSI ports. The group does NOT use a dedicated management port.
What is the correct sequence of steps to change all physical and group IPs on the members to the new subnet?
  1. A
    - Change 1st port array physical ports first - Change Group IP second - Change 2nd port array physical ports last
  2. B
    - Change Group IP first - Change 2nd port array physical ports second - Change 1st port array physical ports last
  3. C
    - Change 1st port array physical ports first - Change 2nd port array physical ports second - Change Group IP last
  4. D
    - Change 2nd port array physical ports first - Change Group IP second

Correct Answer:
C
Note:
* Changing the group IP address disconnects any iSCSI connections to the group and any administrators logged in to the group through the group IP address.
* If you change the IP address of a group for which you are running the GUI locally, or configure a management network for the group, you must uninstall the standalone GUI application and then install it again.
References:
http://psonlinehelp.equallogic.com/en/V6.0/groupmanager.htm
(About Group Network Configuration)

Previous Questions Next Questions

All Pages