Nest 0 Cart
Nest Account
Popular Exams
All Categories...
Nest
Nest 0
Contact
Log In / Sign Up
Copyright 2024 © store. All rights reserved.
Home Cisco® 300-410

Cisco® 300-410 Exam Practice Questions (P. 2)

  • Full Access (620 questions)
  • Six months of Premium Access
  • Access to one million comments
  • Seamless ChatGPT Integration
  • Ability to download PDF files
  • Anki Flashcard files for revision
  • No Captcha & No AdSense
  • Advanced Exam Configuration
Get Contributor Access
Question #11
Refer to the exhibit. R2 is a route reflector, and R1 and R3 are route reflector clients. The route reflector learns the route to 172.16.25.0/24 from R1, but it does not advertise to R3.
What is the reason the route is not advertised?

  1. A
    R2 does not have a route to the next hop, so R2 does not advertise the prefix to other clients.
  2. B
    Route reflector setup requires full IBGP mesh between the routers.
  3. C
    In route reflector setup, only classful prefixes are advertised to other clients.
  4. D
    In route reflector setups, prefixes are not advertised from one client to another.

Correct Answer:
A

Question #12

Refer to the exhibit. An engineer is trying to redistribute OSPF to BGP, but not all of the routes are redistributed.
What is the reason for this issue?
  1. A
    By default, only internal routes and external type 1 routes are redistributed into BGP
  2. B
    Only classful networks are redistributed from OSPF to BGP
  3. C
    BGP convergence is slow, so the route will eventually be present in the BGP table
  4. D
    By default, only internal OSPF routes are redistributed into BGP

Correct Answer:
D

Question #13

Refer to the exhibit. In which circumstance does the BGP neighbor remain in the idle condition?
  1. A
    if prefixes are not received from the BGP peer
  2. B
    if prefixes reach the maximum limit
  3. C
    if a prefix list is applied on the inbound direction
  4. D
    if prefixes exceed the maximum limit

Correct Answer:
D

Question #14
Which attribute eliminates LFAs that belong to protected paths in situations where links in a network are connected through a common fiber?
  1. A
    shared risk link group-disjoint
  2. B
    linecard-disjoint
  3. C
    lowest-repair-path-metric
  4. D
    interface-disjoint

Correct Answer:
B
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_eigrp/configuration/xe-3s/asr1000/ire-xe-3s-asr1000/ire-ipfrr.html

Question #15

Refer to the exhibit. An engineer is troubleshooting BGP on a device but discovers that the clock on the device does not correspond to the time stamp of the log entries.
Which action ensures consistency between the two times?
  1. A
    Configure the service timestamps log uptime command in global configuration mode.
  2. B
    Configure the logging clock synchronize command in global configuration mode.
  3. C
    Configure the service timestamps log datetime localtime command in global configuration mode.
  4. D
    Make sure that the clock on the device is synchronized with an NTP server.

Correct Answer:
D

Question #16
Refer to the exhibit. What is the result of applying this configuration?

  1. A
    The router can form BGP neighborships with any other device.
  2. B
    The router cannot form BGP neighborships with any other device.
  3. C
    The router cannot form BGP neighborships with any device that is matched by the access list named ג€BGPג€.
  4. D
    The router can form BGP neighborships with any device that is matched by the access list named ג€BGPג€.

Correct Answer:
A

Question #17
Which command displays the IP routing table information that is associated with VRF-Lite?
  1. A
    show ip vrf
  2. B
    show ip route vrf
  3. C
    show run vrf
  4. D
    show ip protocols vrf

Correct Answer:
B
Reference:
https://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/12-2/50sg/configuration/guide/Wrapper-46SG/vrf.html#wp1045708

Question #18

Refer to the exhibit. Which subnet is redistributed from EIGRP to OSPF routing protocols?
  1. A
    10.2.2.0/24
  2. B
    10.1.4.0/26
  3. C
    10.1.2.0/24
  4. D
    10.2.3.0/26

Correct Answer:
A

Question #19
Which configuration adds an IPv4 interface to an OSPFv3 process in OSPFv3 address family configuration?
  1. A
    router ospfv3 1 address-family ipv4
  2. B
    Router(config-router)#ospfv3 1 ipv4 area 0
  3. C
    Router(config-if)#ospfv3 1 ipv4 area 0
  4. D
    router ospfv3 1 address-family ipv4 unicast

Correct Answer:
D
Reference:
https://www.cisco.com/c/en/us/td/docs/ios-xml/ios/iproute_ospf/configuration/xe-3s/iro-xe-3s-book/ip6-route-ospfv3-add-fam-xe.html

Question #20

Refer to the exhibit. Which statement about R1 is true?
  1. A
    OSPF redistributes RIP routes only if they have a tag of one.
  2. B
    RIP learned routes are distributed to OSPF with a tag value of one.
  3. C
    R1 adds one to the metric for RIP learned routes before redistributing to OSPF.
  4. D
    RIP routes are redistributed to OSPF without any changes.

Correct Answer:
B

Previous Questions Next Questions

All Pages