Nest 0 Cart
Nest Account
Popular Exams
All Categories...
Nest
Nest 0
Contact
Log In / Sign Up
Copyright 2024 © store. All rights reserved.
Home HP HP2-Z34

HP HP2-Z34 Exam Practice Questions (P. 5)

  • Full Access (60 questions)
  • Six months of Premium Access
  • Access to one million comments
  • Seamless ChatGPT Integration
  • Ability to download PDF files
  • Anki Flashcard files for revision
  • No Captcha & No AdSense
  • Advanced Exam Configuration
Get Contributor Access
Question #21
Refer to the exhibits -

Exhibit 1 -


This data center topology is being set up to use SPBM. VMs in the same subnet should be able to communicate at Layer 2 and be isolated at Layer 2 from other subnets. VS110010 was created for VLAN 10 as shown in Exhibit 2. The administrator is configuring a service instance for the VLAN 10 traffic on Switch 1 interface Ten1/0/1.
What is the correct encapsulation mode?
  1. A
    s-vid101
  2. B
    ta99ed
  3. C
    default
  4. D
    s-vid10

Correct Answer:
D

Question #22
Refer to the exhibit -

These switches form an SPBM region. What is required for load balancing to occur across the links between these switches?
  1. A
    IS-IS cost for each backbone link must be the same (with IS-IS ECMP enabled).
  2. B
    B-VLANs must be configured to use different ECT algorithms.
  3. C
    Tandem multicast mode must be enabled globally
  4. D
    B-VLANs must be assigned to different MSTP instances.

Correct Answer:
C

Question #23
To support FCoE traffic, a switch port needs to use Application TLVs to communicate application priority information to a Converged Network Adapter (CNA). The setup process includes the configuration of an Access Control List (ACL). What is a valid ACL?
  1. A
    Advanced ACL that selects traffic by UDP source port
  2. B
    Advanced ACL that selects traffic by TCP source port
  3. C
    Standard ACL that selects traffic by source IP address
  4. D
    Ethernet ACL that selects traffic by Ethertype

Correct Answer:
B

Question #24
Refer to the exhibit -

useOSPF
have established an MPLS domain.
use LDP.
have established a Martini Layer 2 VPN between Sites 1 and 2
VPN traffic is using the link between PE-1 and P-4, and this link fails.
What happens to the VPN traffic?
  1. A
    It is disrupted for this particular site-to-site connection until the link is fixed
  2. B
    It fails over to the link between PE-1 and P-5 only //administrators created a backup virtual circuit (VC) from PE-1 to
  3. C
    It fails over to the link between PE-1 and P-5 only if administrators created two virtual circuits (VCs) between PE-1
  4. D
    and PE-2.
  5. E
    It fails over to the link between PE-1 and P-5. The failover is automatically handled by MPLS. LDP, and OSPF

Correct Answer:
A

Question #25
An HP Comware switch port is being connected to a server Converged Network Adaptor (CNA). The CNA and the switch port need to communicate about parameters for various priority flow control (PFC) and bandwidth control mechanisms. How does the administrator enable these communications?
  1. A
    Enable PFC globally and then enable PFC on the switch port
  2. B
    Enable the Fibre Channel (FC) fabric port function on the switch port and then set the port as an F-port.
  3. C
    Enable Ethernet Virtual Bridging (EVB) on the switch port.
  4. D
    Enable LLDP globally and then enable Data Center Bridging eXchange (DCBX) TLVs on the switch port

Correct Answer:
D

Previous Questions Next Questions

All Pages