Nest 0 Cart
Nest Account
Popular Exams
All Categories...
Nest
Nest 0
Contact
Log In / Sign Up
Copyright 2024 © store. All rights reserved.
Home Cisco® 200-125

Cisco® 200-125 Exam Practice Questions (P. 4)

  • Full Access (1926 questions)
  • Six months of Premium Access
  • Access to one million comments
  • Seamless ChatGPT Integration
  • Ability to download PDF files
  • Anki Flashcard files for revision
  • No Captcha & No AdSense
  • Advanced Exam Configuration
Get Contributor Access
Question #31
Refer to the exhibit.
A network administrator configures a new router and enters the copy startup-config running-config command on the router.
The network administrator powers down the router and sets it up at a remote location.
When the router starts, it enters the system configuration dialog as shown. What is the cause of the problem?

  1. A
    The network administrator failed to save the configuration.
  2. B
    The configuration register is set to 0x2100.
  3. C
    The boot system flash command is missing from the configuration.
  4. D
    The configuration register is set to 0x2102.
  5. E
    The router is configured with the boot system startup command.

Correct Answer:
A

Question #32
Refer to the exhibit. What can be determined about the router from the console output?

  1. A
    No configuration file was found in NVRAM.
  2. B
    No configuration file was found in flash.
  3. C
    No configuration file was found in the PCMCIA card.
  4. D
    Configuration file is normal and will load in 15 seconds.

Correct Answer:
A

Question #33
When you are troubleshooting an ACL issue on a router, which command can help you to verify which interfaces are affected by the ACL?
  1. A
    show access-lists
  2. B
    show interface
  3. C
    show ip interface
  4. D
    show ip access-lists
  5. E
    list ip interface

Correct Answer:
C

Question #34
Which router IOS commands can be used to troubleshoot LAN connectivity problems? (Choose three.)
  1. A
    winipcfg
  2. B
    tracert
  3. C
    ping
  4. D
    ip config
  5. E
    show ip route
  6. F
    show interfaces

Correct Answer:
CEF

Question #35
Refer to the exhibit.

What is the reason that the interface status is "administratively down, line protocol down"?
  1. A
    There is no encapsulation type configured.
  2. B
    There is a mismatch in encapsulation types.
  3. C
    The interface is not receiving any keepalives.
  4. D
    The interface has been configured with the shutdown command.
  5. E
    The interface needs to be configured as a DTE device.
  6. F
    The wrong type of cable is connected to the interface.

Correct Answer:
D

Question #36
What is a global command?
  1. A
    a command that is set once and affects the entire router.
  2. B
    a command that is implemented in all foreign and domestic IOS versions.
  3. C
    a command that is universal in application and supports all protocols.
  4. D
    a command that is available in every release of IOS, regardless of the version or deployment status.
  5. E
    a command that can be entered in any configuration mode.

Correct Answer:
A

Question #37
What should be done prior to backing up an IOS image to a TFTP server? (Choose three)
  1. A
    Make sure that the server can be reached across the network.
  2. B
    Check that authentication for TFTP access to the server is set.
  3. C
    Assure that the network server has adequate space for the IOS image.
  4. D
    Verify file naming and path requirements.
  5. E
    Make sure that the server can store binary files.
  6. F
    Adjust the TCP window size to speed up the transfer.

Correct Answer:
ACD

Question #38
At which layer of the OSI model does the IPSec operate?
  1. A
    Application
  2. B
    Network
  3. C
    Transport
  4. D
    Data-link

Correct Answer:
B

Question #39
Which command can you use to manually assign a static IPv6 address to a router interface?
  1. A
    ipv6 address PREFIX_1::1/64
  2. B
    ipv6 autoconfig 2001:db8:2222:7272::72/64
  3. C
    ipv6 autoconfig
  4. D
    ipv6 address 2001:db8:2222:7272::72/64

Correct Answer:
D

Question #40
The network administrator is asked to configure 113 point-to-point links. Which IP addressing scheme best defines the address range and subnet mask that meet the requirement and waste the fewest subnet and host addresses?
  1. A
    10.10.0.0/18 subnetted with mask 255.255.255.252
  2. B
    10.10.0.0/25 subnetted with mask 255.255.255.252
  3. C
    10.10.0.0/24 subnetted with mask 255.255.255.252
  4. D
    10.10.0.0/23 subnetted with mask 255.255.255.252
  5. E
    10.10.0.0/16 subnetted with mask 255.255.255.252

Correct Answer:
D

Previous Questions Next Questions

All Pages