Nest 0 Cart
Nest Account
Popular Exams
All Categories...
Nest
Nest 0
Contact
Log In / Sign Up
Copyright 2024 © store. All rights reserved.
Home Cisco® 200-601

Cisco® 200-601 Exam Practice Questions (P. 2)

  • Full Access (67 questions)
  • Six months of Premium Access
  • Access to one million comments
  • Seamless ChatGPT Integration
  • Ability to download PDF files
  • Anki Flashcard files for revision
  • No Captcha & No AdSense
  • Advanced Exam Configuration
Get Contributor Access
Question #6
It is common to use Resilient Ethernet Protocol (REP) on the manufacturing floor as a resiliency protocol, as opposed to the Enterprise where it is not generally deployed. What are two reasons why REP is more suitable for the plant floor? (Choose two)
  1. A
    REP is only supported on Industrial Ethernet switches, it is not supported on Catalyst switches.
  2. B
    REP converges faster than Spanning Tree, allowing for greater network availability.
  3. C
    REP supports Industrial Ethernet protocols better because it moves the packets faster.
  4. D
    Running dual cables from access switches to an aggregation switch can have a much higher cost on the plant floor than in the Enterprise and running a ring protocol like REP provides resiliency at a lower cost.
  5. E
    Industrial protocols can be negatively impacted by the number of nodes the Ethernet frame traverses, REP provides a topology with no more than 3 nodes for

Correct Answer:
BD

Question #7
Which five are characteristics that describe Cisco Industrial switches? (Choose five)
  1. A
    Din rail mount
  2. B
    19 inch rack mount
  3. C
    Fanless
  4. D
    Fans
  5. E
    Swappable SD flash card
  6. F
    Alarm relay
  7. G
    -5ºC to 45ºC operating environment
  8. H
    ProfiNET conformance class C compliance

Correct Answer:
ABCEF

Question #8
Which selection is a reason why IGMP snooping should be configured on a switched network?
  1. A
    IGMP snooping populates the snooping table with the results of DHCP requests and can be used by Dynamic ARP Inspection to block IP spoofing attacks at Layer-2.
  2. B
    IGMP snooping verifies the source IP address of every IPv4 packet to ensure that it hasn't been originated from a port different than its return path.
  3. C
    IGMP snooping is used to filter ping requests and results to avoid overflowing the MAC address table of the switch.
  4. D
    IGMP snooping allows a Layer-2 switch to limit the transmission of multicast frames to only the ports that have members of the relevant IGMP group.

Correct Answer:
D

Question #9
Refer to the exhibit.

Which three options are needed to configure NAT on router GW so PC1 and PC2 will be able to ping 203.0.113.1? (Choose three)
  1. A
    interface Ethernet0 ip nat inside interface Ethernet1 ip nat outside
  2. B
    ip access-list standard ACL_NAT permit 10.1.1.0 0.0.0.255
  3. C
    ip nat inside source static tcp 10.1.1.0 80 interface Ethernet1 80
  4. D
    interface Ethernet0 ip nat outside interface Ethernet1 ip nat inside
  5. E
    ip nat inside source list ACL_NAT interface Ethernet1 overload
  6. F
    ip access-list extended ACL_NAT

Correct Answer:
ABE

Question #10
Refer to the exhibit.

NAT has been configured on the router 'GW' and the IP addresses of router 'GW' have been configured properly. Users of PC1 and PC2 are able to ping the IP address 198.51.100.1 but are unable to reach any other IP addresses on the Internet. The ISP confirmed that their configuration is correct. Which option would likely correct the problem?
  1. A
    ip access-list extended ACL_OUTBOUND permit ip 10.1.1.0 0.0.0.255 any interface Ethernet1 ip access-group ACL_OUTBOUND out
  2. B
    interface Ethernet1 ip nat outside
  3. C
    interface Ethernet0 ip nat inside
  4. D
    ip route 0.0.0.0 0.0.0.0 198.51.100.1

Correct Answer:
D

Previous Questions Next Questions

All Pages